1 5

Chromaline

ChromaLime (Émulsion)

ChromaLime (Émulsion) - 1 unité (1 gallon)

SKU:

$100.00 CAD
$100.00 CAD $100.00 CAD
Vente Épuisé
Frais d'expédition calculés à l'étape de paiement.

Remarque : Il n'est pas recommandé d'expédier l'émulsion lorsque la température est inférieure au point de congélation. Veuillez acheter à vos propres risques, car nous ne pouvons garantir l'intégrité de l'émulsion si le gel se produit pendant le transport. Toutes les commandes d'émulsion passées par temps froid sont des ventes finales.

 

ChromaLime est une émulsion photopolymère pure vert citron, conçue pour les environnements d'atelier avec des niveaux d'humidité élevés. Idéale pour les ateliers cherchant à éliminer l'adhérence des positifs de film sur les écrans enduits pendant le processus d'exposition. Comparable aux émulsions photopolymères pures ChromaBlue et CTR.

 

  • Optimisée pour les systèmes d'exposition LED et UV traditionnels
  • Exposition très rapide
  • Élimine/réduit considérablement l'adhérence aux positifs de film et à la vitre de l'unité d'exposition
  • Non collante dans des conditions de forte humidité
  • Améliore la résolution et la définition
  • Translucidité optimale pour un repérage facile et des réglages de presse plus rapides
  • Idéale pour les systèmes de récupération automatisés
  • ChromaLime est mieux utilisée avec les encres plastisol pour textiles, permettant une installation de presse plus rapide et une meilleure récupérabilité.
Taille

In stock

disabled

Product Resources

Afficher tous les détails

Souvent achetés avec

 



 

Additional Information

Work Under Yellow Lights.

 

  • DEGREASE

Work up a lather on both sides of mesh to degrease. Be sure to use only a high-quality mesh degreaser, such as Chroma/Clean designed specifically for this purpose. Rinse thoroughly.

 

  • COAT

Fill scoop coater with room temperature emulsion. Slowly apply first coat to print side. Next, coat squeegee side with 1-3 coats depending upon thickness required. For most art, a 1X1 coating will be optimal. If a thicker stencil is required, apply additional wet-on-wet coatings from the squeegee side.

 

Note:

• ChromaLime is presensitized. Stir before use.

• Keep pail covered when not in use.

• Return unused emulsion from scoop coater to pail as soon as possible. Emulsion dries quickly and will rapidly "skin over."

 

  • DRY

Dry screen thoroughly in horizontal position with print side down, using a completely clean and dark drying cabinet. Temperature should not exceed 110ºF (43ºC).

 

  • EXPOSE

Using the 10-Step Exposure Guide to determine proper exposure times for ChromaBlue, place emulsion side of photopositive in contact with print side of screen. Exposure times for ChromaBlue are very short and accurate exposure is important for optimal results. See exposure guidelines at right.

 

  • DEVELOP

Gently spray both sides of screen with lukewarm water, wait 30 seconds then gently wash print side of the screen until image is fully open. Rinse both sides thoroughly. Dry screen completely and you are ready to print.

 

  • RECLAIM

Apply a high quality screen reclaimer, such as Chroma/Strip to both sides. Scrub area to be reclaimed with a stiff nylon brush to ensure entire surface is wet and let sit until stencil begins to dissolve. Remove stencil residue with pressure washer, then rinse with hose, thoroughly flooding screen and frame.

 

*Do not let reclaimer dry

 

EXPOSURE GUIDELINES

Note: Exposure times are suggested only as a guide. Individual exposure times may vary depending upon equipment used, bulb age, and other shop conditions. Suggested exposure times are as follows:

 

QuickImage LED exposure system: 1x1 round edge coating 10-20 seconds on 110 white mesh 18-22 seconds on 110 yellow mesh

 

Exposure times below were set for 5KW unit at 40" from frame.

 

110 YELLOW POLYESTER - MONOFILAMENT MESH
Coating Technique Coater Edge Suggested Min. Exp. Time
1x1 Round 30 sec.
1x2 Round 40 sec.
1x3 Round 50 sec.

 

230 YELLOW POLYESTER - MONOFILAMENT MESH
Coating Technique Coater Edge Suggested Min. Exp. Time
1x1 Round 20 sec.
1x2 Round 25 sec.
1x3 Round 30 sec.

 

390 YELLOW POLYESTER - MONOFILAMENT MESH
Coating Technique Coater Edge Suggested Min. Exp. Time
1x1 Round 15 sec.
1x2 Round 20 sec.
1x3 Round 25 sec.

 

* Exposure times were determined using the Chromaline Exposure Calculator.

  • Color: Lime Green
  • Solids: 40%
  • Viscosity: Medium-High
  • Easier on-press registration = more setups/day
  • Resists humidity = tack-free
  • Excellent Reclaimability - Go Ahead, Try Me

ChromaLime emulsion should be stored at room temperature and should not be stored at temperatures above 80°F (27°C) or below 32°F (0°C). ChromaLime emulsion should be stored in its original container.

 

Protect from freezing. ChromaLime is not freeze/thaw stable.